HA Parameters

The High Availability (HA) parameters are described in the table below.

When configuration is applied to the device whose MAC is the value of the HARemoteMAC parameter, all HA configuration is swapped between local and remote parameters, including the IP address of the Maintenance interface, which is swapped with the address configured for the HARemoteAddress parameter. For more information, see Quick-and-Easy Initial HA Configuration.

HA Parameters

Parameter

Description

[HAMaintenanceIFDiffServValue]

Defines the DiffServ value for HA Maintenance traffic flowing on the HA Maintenance interface.

The valid value is 0 (lowest priority or best-effort service) to 63 (highest priority). The default is 46.

Note: For the parameter to take effect, a device restart is required.

 

configure network > high-availability settings > operational-state-delay

[HAOperationalStateDelayInSec]

Defines the duration (in seconds) to delay the transition from HA non-operational state, which occurs during HA synchronization between active and redundant devices, to HA operational state. This feature may be useful, for example, to delay HA switchover when using switches with spanning tree protocol (STP) that take a long time until their ports (to which the redundant device is connected) is ready. In such a scenario, if this feature were not enabled (i.e., 0), after synchronization there would be no connectivity between the redundant device's network interface and the switch.

The valid value is 0 to 180. The default is 0.

[HALocalMAC]

Specifies the MAC address of one of the two devices in the HA system.

For more information, see Quick-and-Easy Initial HA Configuration.

Note: When downloading an ini file from a device that is operating in HA mode, the parameter is the MAC address of the active device.

[HARemoteMAC]

Specifies the MAC address of one of the two devices in the HA system.

For more information, see Quick-and-Easy Initial HA Configuration.

Note: When downloading an ini file from a device that is operating in HA mode, the parameter is the MAC address of the redundant device.

'HA Device Name'

configure network > high-availability settings > unit-id-name

[HAUnitIdName]

Defines a name for the active device, which is displayed on the Home page to indicate the active device.

The valid value is a string of up to 128 characters. The default value is "Device 1".

Note: When the device sends alarms to OVOC, this name is displayed at the beginning of the alarm description in OVOC, for example, "(SBCSITE01): Proxy lost. looking for another proxy". However, the name is not displayed for the alarms retrieved (from the device's Active Alarms table) when OVOC initially connects to the device.

'HA Remote Device Name’

configure network > high-availability settings > redundant-unit-id-name

[HARemoteUnitIdName]

Defines a name for the redundant device, which is displayed on the Home page to indicate the redundant device.

The valid value is a string of up to 128 characters. The default value is "Device 2".

Note: When the device sends alarms to OVOC, this name is displayed at the beginning of the alarm description in OVOC, for example, "(SBCSITE02): Proxy lost. looking for another proxy". However, the name is not displayed for the alarms retrieved (from the device's Active Alarms table) when OVOC initially connects to the device.

'HA Remote Address'

configure network > high-availability settings > remote-address

[HARemoteAddress]

Defines the Maintenance interface address of the redundant device in the HA system.

By default, no value is defined.

Note: For the parameter to take effect, a device restart is required.

'Preempt Mode'

configure network > high-availability settings > revertive-mode

[HARevertiveEnabled]

Enables HA switchover based on HA priority.

[0] Disable = (Default) A switchover over to the redundant device is done only if a failure occurs in the currently active device.
[1] Enable = A switchover over to the redundant device is done if a failure occurs in the currently active device. However, a switchover to the device with the highest priority (configured by the HAPriority parameter) occurs whenever the device recovers from a failure. Therefore, whenever possible, the highest priority device is the active one.

For more information on the HA switchover mechanism, see Device Switchover upon Failure.

'Preempt Priority'

configure network > high-availability settings > priority

[HAPriority]

Defines the priority of the active device used in the HA Preempt mechanism.

The valid value is 1 (lowest priority) to 10 (highest priority). The default is 5.

Note:

The parameter is applicable only if you configure the 'Preempt Mode' parameter to Enable.
You must configure each device in the HA system with different parameter values (priorities).

'HA Remote Preempt Priority'

configure network > high-availability > redundant-priority

[HARemotePriority]

Defines the priority of the redundant device used in the HA Preempt mechanism.

The valid value is 1 (lowest priority) to 10 (highest priority). The default is 5.

Note:

The parameter is applicable only if you configure the 'Preempt Mode' parameter to Enable.
You must configure each device in the HA system with different parameter values (priorities).

HA Network Monitor Parameters

For more information, see Monitoring IP Entities and HA Switchover upon Ping Failure.

'HA Network Monitor'

configure network > high-availability settings > network-monitor-enabled

[HAPingEnabled]

Enables the HA Network Monitor feature, which checks connectivity with network destinations, using pings. When a user-defined number of destinations fail the connectivity test (see 'Network Monitor Threshold' parameter), an HA switchover occurs.

[0] Disable (default)
[1] Enable

'Monitor Threshold'

configure network > high-availability settings > network-monitor-threshold

[HaNetworkMonitorThreshold]

Defines the minimum number of monitored rows (configured in the HA Network Monitor table) whose destinations are unreachable that are required to trigger an HA switchover.

The valid value is 1 to 10. The default is 1.