settings

Enables 911 Location Id in NI2 protocol.

Additional information element to send in ISDN Setup message.

Prefix added to Redirect phone number.

AMD Detection Timeout <msec>.

ISDN B-Channel negotiation mode for all trunks.

Search for Redirect number coded in binary 4 bit style.

Add keying sequence for performing blind transfer as transfer number prefix.

Maximum time (milliseconds) to wait for disconnect from Tel before performing blind transfer.

Hookflash forwarding.

Enables CIC -> ISDN TNS IE interworking.

Enables presentation in the outgoing SIP message when the incoming ISDN message doesn't include presentation.

Enables presentation in the outgoing SIP message when the presentation indicator in the incoming ISDN message has the value "not available".

Charge Indicator Mode.

In use with G.729 - if enabled and SCE=2 then AnnexB=no.

Enables sending of Reason for Non Notification of Caller Id.

FXS: generate Caller Id signals during ringing FXO: collect Caller Id and use it in Setup message.

In case there is an empty source number from PSTN the source number will be the same as the destination.

Copy Destination Number to Redirect Number.

Calling Party Category Mode.

Enables interworking between the ISDN Closed User Group (CUG) supplementary service and SIP, for Tel-to-IP calls.

Enable call connection without On-Hook/Off-Hook process 'Cut-Through'.

Duration of reorder tone played after release from IP side for CutThrogh application

SIP Default Call Priority.

Common cause value to use for most ISDN release causes.

Digital OOS Behavior.

If set to 1 and ISDN DISCONNECT with PI is received, 183 with SDP will be sent toward IP only if no IP-to-Tel alternative route exists.

Disconnect Call on Busy Tone Detection – CAS.

Disconnect Call on Busy Tone Detection – ISDN.

RTP DSCP for MLPP Flash.

RTP DSCP for MLPP Flash Override.

RTP DSCP for MLPP Flash-Override-Override.

RTP DSCP for MLPP Immediate.

RTP DSCP for MLPP Priority.

RTP DSCP for MLPP Routine.

Enforce this Q.931 Destination Number Type.

Enforce this Q.931 Destination Number Type.

Send DTMFs on the Signaling path (not on the Media path).

Defines the MLPP E911 Preemption mode.

If set to 1, AMD detection is started on PSTN alerting otherwise on connect.

Max time (in seconds) to wait from sending Setup message to PSTN to receiving Connect message from PSTN.

Use endpoint number as calling number for IP-to-Tel.

Use endpoint number as calling number for Tel-to-IP.

Use supplementary service ETSI Diverting Leg Information 2 to send redirect number.

Disable fallback from ISDN call transfer to TDM.

Defines the time interval (in sec) to wait for CNG detection to re-route call to fax destinations.

Enables the detection of the fax CNG tone in incoming calls, before sending the INVITE.

Defines the index of the first Call Waiting tone in the Call Progress Tones file.

Defines if the destination phone number that the device sends to the Tel side (for IP-to-Tel calls) includes the user-part parameters (e.g., 'password' and 'phone-context') of the destination URI received in the incoming SIP INVITE message.

Uses the software watchdog for gateway tasks.

Defines gateway H.323-ID source field.

Enable ignoring of ISDN Disconnect messages with PI 1 or 8.

Defines the channel number format (number or slotmap) in the Channel Identification IE when sending Q.931 ISDN messages.

Enables interworking SIP 18x without SDP and ISDN Q.931 Progress/Alerting messages.

Defines SIP-ISDN interworking between NTT Japan's No-ID cause in the Facility information element (IE) of the ISDN Setup message, and the calling party number (display name) in the From header of the SIP INVITE message.

Defines whether the device sends Q.931 Progress messages to the ISDN trunk if the trunk is configured as User side (TE) and/or Network (NT) side, for IP-to-Tel calls.

Interwork of Alert from ISDN to SIP.

Ignore LOS alarms for BRI user side trunk.

IP to CAS list of ANI and DNIS delimiters.

Enable ISDN Facility Trace.

ISDN SubAdress format.

Enable ISDN Tunneling IP to Tel.

Enable ISDN Tunneling Tel to IP.

Send TBCT/ECT/RLT request only when second leg call is connected.

If such a cause received in ISDN DISCONNECT message of the first leg, NOTIFY 200 is sent toward IP.

ISO 8859 Character Set Part.

Number of digits that will be taken from end of phone number as Subaddress.

0 - Don't Send Local Date and Time,1 - Send Local Date and Time Only If Missing,2 - Always Send Local Date and Time

Limit the maximum length in KB for SIP message.

MFC/R2 Calling Party's category.

Enable MFC-R2 protocol debug.

MLPP Default Namespace.

MLPP Default Service Domain String (6 Hex Digits).

MLPP Normalized Service Domain String (6 Hex Digits).

Sets the Network identifier value which is represented as the first 2 octets in the MLPP service domain field. values are [1-999].

Enable/Disable MRD CAS behavior.

Maximum length used for bundling syslog at debug level 7.

Enables NI2 calling party category translation to SIP.

IP Group ID for notification purposes.

Add NPI and TON as prefix to Redirect number.

If selected, ISDN Type & Plan relayed from IP. Otherwise, ISDN Type & Plan are set to 'Unknown'.

Enables Overlap mode.

Progress Indicator for ISDN Setup Message.

Play local RBT on TBCT/ECT/RLT transfer.

Play RB tone on transfer success.

Preemption Tone Duration.

Q850 Reason Code which cause playing special PRT Tone.

Enables QSIG transfer for IP-to-Tel and Tel-to-IP calls.

Enables QSIG Tunneling over SIP.

Defines the format of encapsulated QSIG message data in the SIP message MIME body.

Enable QSIG Transfer Update.

Enable Interworking of Calling Party Category (cpc) from sip INVITE to MFCR2 category for Brazil Telecom.

Send re-INVITE after 181 with new SRTP keys.

Maximum Time to wait between call setup and Facility with Redirecting Number for replacing calling number (msec).

Enable sending restarts to PSTN on channels experienced mismatch in CONNID usage.

Defines if to disconnect call while receiving ISDN PROGRESS with Cause.

Removes calling name from IP > Tel calls.

Removes CLI from IP-to-Tel calls if received CLI is restricted.

RTCP activation policy.

Overrides the screening indicator for the first calling party number when the device includes two calling party numbers in the outgoing ISDN Setup message for IP-to-Tel ISDN calls.

Overrides the screening indicator for the second calling party number when the device includes two calling party numbers in the outgoing ISDN Setup message for IP-to-Tel ISDN calls.

Enable SetupAck messages for overlap mode

SilenceSupp in SDP used for fax VBD

if defined, enforce this Q.931 Source Number Plan

if defined, enforce this Q.931 Source Number Type

Swap Redirect and Called numbers

Time between first INVITE issued within the same trunk (msec)

Minimum connected calls for trunk activation, if 0 - trunk is always active

Time between call release and new INVITE(msec)

Enable gateway to maintain a permanent RTP connection

Enables Third Party Call Control Transcoding functionality

Delay time before playing Reorder tone

In case the transfer capability of a call from ISDN is data open with transparent coder

Trunk alarm call disconnect timeout in seconds

Configure trunk groups on which to send additional IE

Trunk Restart Mode on Power Up.

When TrunkGroup #1 is present and active response to options and/or send keep-alive to associated proxy(ies)

Use the user part of To header URL as called number (IP->TEL)

Provides a link to the user information file, to be downloaded using Automatic Update.

The file name to be loaded using TFTP

Enable User-User IE to pass in Setup from IP to ISDN

Enable User-User IE to pass in Setup from ISDN to IP

Defines the timeout (in milliseconds) to wait for the release ACK from the PSTN before releasing the channel.

Time to wait to detect busy and reorder tones. Currently used in semi supervised PBX transfer

OfHook Warning Tone Duration [Sec]

if set ECT RLT 2BCT call transfer is allowed across different trunks and trunkgroups

0: ISDN Transfer Capability for data calls will be 64k unrestricted (data), 1:ISDN Transfer Capabilityfor Data calls will be set according to ISDNTransferCapability parameter